MOFI4500-4GXeLTE V2 Download/Firmware Update Section:

NOTE THAT IS IT IMPORTANT TO VERIFY YOUR MODEL BEFORE DOING THIS UPDATE

This download is only for the MOFI4500-4GXeLTE V2 version.

If you have a V1 or V3 version, you need to use the other download section.

If you want to see a video on how to do the firmware update, you can look at it here:

https://www.youtube.com/watch?v=7g8SGYDNVbw&t=4s

 

In this download section, there are 3 downloads

– NON SIM firmware (made to work without the module) and to be used for usb tethering 1.9.9std

– For anyone who needs to use IP SEC, there is a special firmware for that, currently 4.3.6IP SEC

– The MAIN firmware to be used with the SIM4, SIM5 and SIM7 model.This is the most popular download, currently firmware 4.4.1std

 

Important Notes:

If you have the basic MOFI4500-4GXeLTE V2 and use a USB modem/hotspot, you should use firmware 1.9.9.9std
For iPhone USB Tethering, you will also need 1.9.9std

For Android USB Tethering, you can use firmware 2.1.8std or later

AllSIM4 routers should use firmware 2.1.8 or later for all providers
(if you have any issues with disconnect, it is recommended to use thisfirmware 2.1.8 or later firmware, read below on how to update)

For SIM3, you should use firmware 1.9.9std

Note if you are using a SIM4 with Sprint that was activated using the mofi router, you should use the latest std firmware

If ou need to USB tether your iphone, you need to use firmware 1.9.9std

If your router does not have the power light on after 1 minute for manyreasons, you can use this recovery file to bring your unit back up

 

MOFI RECOVERY INSTRUCTIONS:

—————————————————————————————————————–
If your router’s power does not come on and flash or have an issues that is serious,
you can try to do a recovery as it is possible to have this fixed.

https://mofinetwork.com/firmware/mofi4500v2/MOFI_RECOVERY _MOFI4500_models.pdf

——————————————————————————————————————

 

Firmware 4.4.1std (For all providers)
Date Released: Jan 13 2021

———————————————————————————————————————–

CLICK HERE TO SAVE FIRMWARE 4_4_1std
https://mofinetwork.com/firmware/mofi4500v2/mofi4500_4GXeLTE_V2Firmware4_4_1std.bin

Checksum: de310ddcd33c8621a56f5708f0f98fd8

Change Logs:

– 4.4.1 Roaming on SIM card is set to OFF by default. Can be turned on if needed
– 4.4.1 Setting for RING DOORBELL available under System – Misc Settings
– 4.4.1 Updated USB Printer settings
– 4.3.6 Fixed bandwidth monitor reset scheduling
– 4.3.4 IP V6 Updated with bug fixes (note IP V6 is off by default but can be turned on in GUI)
– 4.3.2 Fixed Band Scanner Issues
– 4.3.2 Fixed Band Lock sometimes not locking correct
– 4.3.1 Fixed reconnect issue with the SIM7 model
– 4.3.0 Updated re-connection option to specify website pings
– 4.3.0 Updated Security patch
– 4.2.9 Fixed some re-connection issues on all networks including Verizon and T-Mobile
– 4.2.9 Fix Speed Throttling Option via MAC address (can now speed throttle by device)
– 4.2.8 Fixed some re-connection issues on ATT
– 4.2.7 Added ability to set speed per mac address
– 4.2.5 Fixed some gui issues introduced on 4.2.4
– 4.2.4 Upgraded OpenVPN GUI interface
– 4.2.4 New Cloud Link Server Add
– 4.2.0 Updated IP Pass Through Setting
– 4.1.8 Fixed Purevpn issue
– 4.1.7 Changed TTL to default at 64 instead of 65 as 64 seems to have faster speeds
– 4.1.7 Default SIM4 module to generic modem
– 4.1.7 Fix SIM card installed in SIM7 not showing correct status
– 4.1.5 Fix router management issue
– 4.1.5 Fix Purevpn where you can add mac address in split tunnel mode
– 4.1.3 Implemented new free remote management portal to manage router remotely
– 4.1.2 Fixed Reboot issue where in 4.0.9std, after you run the wizard, it was not rebooting to apply the password change
– 4.0.9 Added current access point at the bottom page to view the apn that is selected
– 4.0.8 SIM7 loaded in default mode where it can receive band 66 if available easier
– 4.0.6 Fixed issue with Verizon APN getting wiped out
– 4.0.4 Fixed Time out screen when disabling some VPN services
– 4.0.3 Fixed Band Locking for band 66 and 71 on the SIM7 model
– 4.0.3 Fixed USB Tethering issue on Samsung S7
– 4.0.1 Fixed Pure with no compression options
– 4.0 Support for the MOFI4500-4GXeLTE-SIM7

Instructions on how to update the router:

To do the firmware update, you must connect to the router with a network cable from your pc to the router.
Take out the 3G/4G/LTE stick from the back of the router

You should not use Google Chrome to do the firmware update or anything else when you log into the router.
Use Internet Explorer, Firefox or Safari web browser to do this update.

1) Power on router and connect to port 1-4 on the back of the router or connect to the wifi network on the router

2) After router is completed booting up (takes approx 60 seconds) andpower light is solid, open up your internet explorer, firefox or safari
(do not use Google Chrome)

3) In the address bar, enter
http://192.168.10.1/cgi-bin/luci
username: root
password: admin

4) Click on basic mode on the top right and then click on the system system on the side

5) Click on Manually Flash Firmware which is located under System

6) Uncheck “Keep Settings” and click on Browse… or Choose File

7) Locate the file that you saved and click on Open

8) Click on “Upload image”
Checksum: de310ddcd33c8621a56f5708f0f98fd8

If the checksum is not the same as listed here, delete the file you have and re-download it.

9) Click “Proceed” to start the update process (may take up to 2 mins).
When the power light startsto blink, the update is completed and the router is rebooting.

10) After update is completed and power light is solid, you will be prompt to log in
If not, make sure you are connect to the router via wifi or Ethernet and go back to the log in

http://192.168.10.1/cgi-bin/luci
username: root
password: admin

11) After you are logged in, do a factory default that is located in basic mode then system then factory default.

Do the default and that would complete all the steps for this update.

————————————————————————————————-

 

Firmware 1.9.9.1std (July 10 2019)

Click HERE
https://mofinetwork.com/firmware/mofi4500v2/mofi4500_4GXeLTE_V2Firmware1_9_9_1std.bin
Save this or just click on it to save but verify that you know where this is being saved.
Normally by default it might go to your download folder

Checksum: df526fd2d51b36ef11f4e6fad9609666
Size: 14.25 MB (31.69 MB available)

————————————————————————————————-

Instructions to install firmware 1.9.9std for the MOFI4500-4GXeLTE V2
Note: If you have a MOFI4500-4GXeLTE V1 model, you need to use the V1 firmware that is in our MOFI4500-4GXeLTE V1 section.
If your router model does not say V2 on it, then it is a V1 model.

Also, iphone and Android USB tethering as well as repeater mode is included in this firmware

If you have the non sim MOFI4500-4GXeLTE, you will need this1.9.9std firmware however, some hotspot support is also included withthe 3.XXX firmware
If you have a MOFI4500-4GXeLTE-SIM3, you will need this firmware
For the MOFI4500-4GXeLTE-SIM2 and SIM4 V2 model, you should use the latest firmware 3.XX firmware

Follow these steps to do the firmware update:

Changes

– 1.9.9 updated Add support for USB730L update fix that was done recently.
– 1.9.8.8 Added new mofi cloud link servers
– 1.9.8.8 Fixed issues with SIM4 if used on this firmware recommend firmware 2.6 or later
-1.9.8.5 Add support for Verizon Mifi 6620L
-1.9.8.5 Fixed Android USB Tethering Issue
– 1.9.8.3 Added support for ZTE Falcon Z17 hotspot
-1.9.8.3 Added support for AT&T MF923Velocity device hotspot
-Fixed ability to disable the cellular module needed
– Added ability to use MOFI CLOUD with IP Pass Through
– Added new MOFI CLOUD East Server
-Fixed IP Pass Through (Can be use with or without a public IP)
-Added Load Balancing with Multi WAN
-Fixed watchdog issue
-Fixed AT&T Disconnect Issue
-Added new MOFI CLOUD SERVERS for static public IP address
-Added more option to read and forward text on SIM model
-Fixed Sprint U341 connection issue
– Fixed Repeater Issue in previous firmware
– Support new SIM4 with auto provider via SIM Card
-Fixed connection issue with MOFI4500-4GXeLTE-SIM2 with firmware 1.4std
-Fixed Wifi Auto Scanning
– Fixed Wifi Issues where wifi might disconnect oftenfor various customers
-Fixed Reset to default bug
-Ability to disable reset button via gui
– fixed bandwidth and internet usage section
– can automatically set bandwidth to all users for public wifi
-Fixed connection issue with Pantech 295 modem
– Fix various bug fixes

Remember to follow the instructions such as making sure you connect your router with a network cable to one of the lan port
(not the wan) to do the firmware update (no wifi)

Instructions on how to update the router:

To do the firmware update, you must connect to the router with a network cable from your pc to the router.
Take out the 3G/4G/LTE stick from the back of the router

You should not use Google Chrome to do the firmware update or anything else when you log into the router.
Use Internet Explorer, Firefox or Safari web browser to do this update.

1) Take the stick out of your router if you are using a 3G/4G/LTE modem or stick if you have one in.

2) Power on router and connect to port 1-4 on the back of the router or connect to the wifi network on the router

3) After router is completed booting up (takes approx 60seconds) and power light is solid, open up your internet explorer,firefox or safari
(do not use Google Chrome)

4) In the address bar, enter
http://192.168.10.1/cgi-bin/luci
username: root
password: admin

5) Click on basic mode on the top right and then click on the system system on the side

6) Click on Manually Flash Firmware which is located under System

7) Uncheck “Keep Settings” and click on Browse… or Choose File

8) Locate the file that you saved and click on Open

9) Click on “Upload image” You should see the file size as 14.25 MB
Checksum: df526fd2d51b36ef11f4e6fad9609666
If the checksum is not the same as listed here, delete the file you have and re-download it.

10) Click “Proceed” to start the update process (may take up to 2 mins).
When the power light startsto blink, the update is completed and the router is rebooting.

11) After update is completed and power light is solid, you will be prompt to log in
If not, make sure you are connect to the router via WiFi or Ethernet and go back to the log in

http://192.168.10.1/cgi-bin/luci
username: root
password: admin

12) After you are logged in, do a factory default that is located in basic mode then system then factory default.

Do the default and that would complete all the steps for this update.

Note that if you want a wifi password, you will need to redo this.
The best way is to click on the wizard on the top left and thewizard will set your router admin password as well as your network nameand wifi security.

If you want to connect to the router with wireless from yourcomputer, just view your available network and you should see yournetwork (default is MofiNetworkXXX) or if you ran the wizard and changethe network name, that should show up now
Click on it to connect and if you set up a wireless password, it will ask you for this,
Enter the password and it will connect you.